※土曜・日曜・祝日の発送はありません。※10月1日より日本郵便値上げの為、送料の変更を行いました。
【玄人向け】【ELRSV2】BetaFPV F4 1S 5A AIO Brushless Flight Controller (ELRSV2 2.4G)
【玄人向け】【ELRSV2】BetaFPV F4 1S 5A AIO Brushless Flight Controller (ELRSV2 2.4G)
¥5,800
SOLD OUT
ELRSV2 2.4G用ロングレンジモジュール
【ELRSV2】BetaFPV F4 1S 5A AIO Brushless Flight Controller (ELRS 2.4G)
※ELRSV2になりますのでご注意ください。
※メーカー出しを通電確認してそのまま送ります。
※VTXは内蔵ではありません。
※この製品は日本語マニュアルもなくかなり設定が難しいので【玄人向け】とさせていただきます。BetaFPVサイトで理解できる方のみご購入下さい。
【玄人向け】マニュアルはありませんので下記URLをご参照に設定してください。
https://betafpv.com/collections/expresslrs-series/products/f4-1s-5a-aio-brushless-flight-controller-elrs-2-4g
【ExpresLRS Radio Link】
https://support.betafpv.com/hc/en-us/sections/4402604654873-ExpresLRS-Radio-Link
ロングレンジELRS受信機内蔵のAIOフライトコントローラー
SPECIFICATIONS OF FC
CPU: STM32F411CEU6 ( 100MHZ )
Six-Axis: ICM-20689/MPU-6000
Built-in Receiver: SPI ExpressLRS 2.4G
Receiver antenna: 2.4GHz SMD ceramic antenna
Size: 29mm x 29mm, fully mounting pattern compatible with the whoop frame in the current market
Firmware version: betaflight_4.3.0_STM32F411_norevision
OSD: Built-in BetaFlight OSD
Recommend VTX: >=200mW, like BETAFPV M03 350mW VTX or TBS Unify VTX
Power Cable: 55mm, with BT2.0 connector
Weight: 3.13g (no power cable included)
SPECIFICATIONS OF ESC
Power supply: 1S
Current: 5A continuous and peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_48_REV16_8.HEX
Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
Betaflight Firmware and CLI
Since Betaflight has not yet released the official firmware that could supports the SPI ExpressLRS protocol, the current version is the Beta version. Please use the firmware and the CLI dump file below to recovery the FC board if needed. Betaflight will update to their official target soon. Please feel free to contact with us if you have any issues with this Beta version Firmware.
It is normal that there is no any option on Betaflight Configurator Receiver. As show below, the checkbox is blank.
PACKAGE
1 * F4 1S brushless flight controller (BT2.0 Connector)
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration rubber dampers
【ELRSV2】BetaFPV F4 1S 5A AIO Brushless Flight Controller (ELRS 2.4G)
※ELRSV2になりますのでご注意ください。
※メーカー出しを通電確認してそのまま送ります。
※VTXは内蔵ではありません。
※この製品は日本語マニュアルもなくかなり設定が難しいので【玄人向け】とさせていただきます。BetaFPVサイトで理解できる方のみご購入下さい。
【玄人向け】マニュアルはありませんので下記URLをご参照に設定してください。
https://betafpv.com/collections/expresslrs-series/products/f4-1s-5a-aio-brushless-flight-controller-elrs-2-4g
【ExpresLRS Radio Link】
https://support.betafpv.com/hc/en-us/sections/4402604654873-ExpresLRS-Radio-Link
ロングレンジELRS受信機内蔵のAIOフライトコントローラー
SPECIFICATIONS OF FC
CPU: STM32F411CEU6 ( 100MHZ )
Six-Axis: ICM-20689/MPU-6000
Built-in Receiver: SPI ExpressLRS 2.4G
Receiver antenna: 2.4GHz SMD ceramic antenna
Size: 29mm x 29mm, fully mounting pattern compatible with the whoop frame in the current market
Firmware version: betaflight_4.3.0_STM32F411_norevision
OSD: Built-in BetaFlight OSD
Recommend VTX: >=200mW, like BETAFPV M03 350mW VTX or TBS Unify VTX
Power Cable: 55mm, with BT2.0 connector
Weight: 3.13g (no power cable included)
SPECIFICATIONS OF ESC
Power supply: 1S
Current: 5A continuous and peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_48_REV16_8.HEX
Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
Betaflight Firmware and CLI
Since Betaflight has not yet released the official firmware that could supports the SPI ExpressLRS protocol, the current version is the Beta version. Please use the firmware and the CLI dump file below to recovery the FC board if needed. Betaflight will update to their official target soon. Please feel free to contact with us if you have any issues with this Beta version Firmware.
It is normal that there is no any option on Betaflight Configurator Receiver. As show below, the checkbox is blank.
PACKAGE
1 * F4 1S brushless flight controller (BT2.0 Connector)
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration rubber dampers
ELRSV2 2.4G用ロングレンジモジュール
【ELRSV2】BetaFPV F4 1S 5A AIO Brushless Flight Controller (ELRS 2.4G)
※ELRSV2になりますのでご注意ください。
※メーカー出しを通電確認してそのまま送ります。
※VTXは内蔵ではありません。
※この製品は日本語マニュアルもなくかなり設定が難しいので【玄人向け】とさせていただきます。BetaFPVサイトで理解できる方のみご購入下さい。
【玄人向け】マニュアルはありませんので下記URLをご参照に設定してください。
https://betafpv.com/collections/expresslrs-series/products/f4-1s-5a-aio-brushless-flight-controller-elrs-2-4g
【ExpresLRS Radio Link】
https://support.betafpv.com/hc/en-us/sections/4402604654873-ExpresLRS-Radio-Link
ロングレンジELRS受信機内蔵のAIOフライトコントローラー
SPECIFICATIONS OF FC
CPU: STM32F411CEU6 ( 100MHZ )
Six-Axis: ICM-20689/MPU-6000
Built-in Receiver: SPI ExpressLRS 2.4G
Receiver antenna: 2.4GHz SMD ceramic antenna
Size: 29mm x 29mm, fully mounting pattern compatible with the whoop frame in the current market
Firmware version: betaflight_4.3.0_STM32F411_norevision
OSD: Built-in BetaFlight OSD
Recommend VTX: >=200mW, like BETAFPV M03 350mW VTX or TBS Unify VTX
Power Cable: 55mm, with BT2.0 connector
Weight: 3.13g (no power cable included)
SPECIFICATIONS OF ESC
Power supply: 1S
Current: 5A continuous and peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_48_REV16_8.HEX
Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
Betaflight Firmware and CLI
Since Betaflight has not yet released the official firmware that could supports the SPI ExpressLRS protocol, the current version is the Beta version. Please use the firmware and the CLI dump file below to recovery the FC board if needed. Betaflight will update to their official target soon. Please feel free to contact with us if you have any issues with this Beta version Firmware.
It is normal that there is no any option on Betaflight Configurator Receiver. As show below, the checkbox is blank.
PACKAGE
1 * F4 1S brushless flight controller (BT2.0 Connector)
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration rubber dampers
【ELRSV2】BetaFPV F4 1S 5A AIO Brushless Flight Controller (ELRS 2.4G)
※ELRSV2になりますのでご注意ください。
※メーカー出しを通電確認してそのまま送ります。
※VTXは内蔵ではありません。
※この製品は日本語マニュアルもなくかなり設定が難しいので【玄人向け】とさせていただきます。BetaFPVサイトで理解できる方のみご購入下さい。
【玄人向け】マニュアルはありませんので下記URLをご参照に設定してください。
https://betafpv.com/collections/expresslrs-series/products/f4-1s-5a-aio-brushless-flight-controller-elrs-2-4g
【ExpresLRS Radio Link】
https://support.betafpv.com/hc/en-us/sections/4402604654873-ExpresLRS-Radio-Link
ロングレンジELRS受信機内蔵のAIOフライトコントローラー
SPECIFICATIONS OF FC
CPU: STM32F411CEU6 ( 100MHZ )
Six-Axis: ICM-20689/MPU-6000
Built-in Receiver: SPI ExpressLRS 2.4G
Receiver antenna: 2.4GHz SMD ceramic antenna
Size: 29mm x 29mm, fully mounting pattern compatible with the whoop frame in the current market
Firmware version: betaflight_4.3.0_STM32F411_norevision
OSD: Built-in BetaFlight OSD
Recommend VTX: >=200mW, like BETAFPV M03 350mW VTX or TBS Unify VTX
Power Cable: 55mm, with BT2.0 connector
Weight: 3.13g (no power cable included)
SPECIFICATIONS OF ESC
Power supply: 1S
Current: 5A continuous and peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_48_REV16_8.HEX
Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
Betaflight Firmware and CLI
Since Betaflight has not yet released the official firmware that could supports the SPI ExpressLRS protocol, the current version is the Beta version. Please use the firmware and the CLI dump file below to recovery the FC board if needed. Betaflight will update to their official target soon. Please feel free to contact with us if you have any issues with this Beta version Firmware.
It is normal that there is no any option on Betaflight Configurator Receiver. As show below, the checkbox is blank.
PACKAGE
1 * F4 1S brushless flight controller (BT2.0 Connector)
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration rubber dampers
ショップの評価
ELRSV2 2.4G用ロングレンジモジュール
【ELRSV2】BetaFPV F4 1S 5A AIO Brushless Flight Controller (ELRS 2.4G)
※ELRSV2になりますのでご注意ください。
※メーカー出しを通電確認してそのまま送ります。
※VTXは内蔵ではありません。
※この製品は日本語マニュアルもなくかなり設定が難しいので【玄人向け】とさせていただきます。BetaFPVサイトで理解できる方のみご購入下さい。
【玄人向け】マニュアルはありませんので下記URLをご参照に設定してください。
https://betafpv.com/collections/expresslrs-series/products/f4-1s-5a-aio-brushless-flight-controller-elrs-2-4g
【ExpresLRS Radio Link】
https://support.betafpv.com/hc/en-us/sections/4402604654873-ExpresLRS-Radio-Link
ロングレンジELRS受信機内蔵のAIOフライトコントローラー
SPECIFICATIONS OF FC
CPU: STM32F411CEU6 ( 100MHZ )
Six-Axis: ICM-20689/MPU-6000
Built-in Receiver: SPI ExpressLRS 2.4G
Receiver antenna: 2.4GHz SMD ceramic antenna
Size: 29mm x 29mm, fully mounting pattern compatible with the whoop frame in the current market
Firmware version: betaflight_4.3.0_STM32F411_norevision
OSD: Built-in BetaFlight OSD
Recommend VTX: >=200mW, like BETAFPV M03 350mW VTX or TBS Unify VTX
Power Cable: 55mm, with BT2.0 connector
Weight: 3.13g (no power cable included)
SPECIFICATIONS OF ESC
Power supply: 1S
Current: 5A continuous and peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_48_REV16_8.HEX
Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
Betaflight Firmware and CLI
Since Betaflight has not yet released the official firmware that could supports the SPI ExpressLRS protocol, the current version is the Beta version. Please use the firmware and the CLI dump file below to recovery the FC board if needed. Betaflight will update to their official target soon. Please feel free to contact with us if you have any issues with this Beta version Firmware.
It is normal that there is no any option on Betaflight Configurator Receiver. As show below, the checkbox is blank.
PACKAGE
1 * F4 1S brushless flight controller (BT2.0 Connector)
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration rubber dampers
【ELRSV2】BetaFPV F4 1S 5A AIO Brushless Flight Controller (ELRS 2.4G)
※ELRSV2になりますのでご注意ください。
※メーカー出しを通電確認してそのまま送ります。
※VTXは内蔵ではありません。
※この製品は日本語マニュアルもなくかなり設定が難しいので【玄人向け】とさせていただきます。BetaFPVサイトで理解できる方のみご購入下さい。
【玄人向け】マニュアルはありませんので下記URLをご参照に設定してください。
https://betafpv.com/collections/expresslrs-series/products/f4-1s-5a-aio-brushless-flight-controller-elrs-2-4g
【ExpresLRS Radio Link】
https://support.betafpv.com/hc/en-us/sections/4402604654873-ExpresLRS-Radio-Link
ロングレンジELRS受信機内蔵のAIOフライトコントローラー
SPECIFICATIONS OF FC
CPU: STM32F411CEU6 ( 100MHZ )
Six-Axis: ICM-20689/MPU-6000
Built-in Receiver: SPI ExpressLRS 2.4G
Receiver antenna: 2.4GHz SMD ceramic antenna
Size: 29mm x 29mm, fully mounting pattern compatible with the whoop frame in the current market
Firmware version: betaflight_4.3.0_STM32F411_norevision
OSD: Built-in BetaFlight OSD
Recommend VTX: >=200mW, like BETAFPV M03 350mW VTX or TBS Unify VTX
Power Cable: 55mm, with BT2.0 connector
Weight: 3.13g (no power cable included)
SPECIFICATIONS OF ESC
Power supply: 1S
Current: 5A continuous and peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_48_REV16_8.HEX
Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
Betaflight Firmware and CLI
Since Betaflight has not yet released the official firmware that could supports the SPI ExpressLRS protocol, the current version is the Beta version. Please use the firmware and the CLI dump file below to recovery the FC board if needed. Betaflight will update to their official target soon. Please feel free to contact with us if you have any issues with this Beta version Firmware.
It is normal that there is no any option on Betaflight Configurator Receiver. As show below, the checkbox is blank.
PACKAGE
1 * F4 1S brushless flight controller (BT2.0 Connector)
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration rubber dampers
