• shopping cart
※土曜・日曜・祝日の発送業務はありません。ご了承下さい。

FC / ESC / レシーバー

【玄人向け】【Frsky / Futaba RX V3.0】BetaFPV F4 1S 5A AIO Brushless Flight Controller 2022  (Frsky / Futaba RX)
【玄人向け】【Frsky / Futaba RX V3.0】BetaFPV F4 1S 5A AIO Brushless Flight Controller 2022 (Frsky / Futaba RX)
BetaFPV F4 1S 5A AIO Brushless Flight Controller 2022 (Frsky / Futaba RX) ※Meteor2022モデル (meteor65 / 65pro / 75 / メーカ出荷)  (Futaba F-SHSS / FrskyX) からお選び下さい。 ※V3.0になります。 ※メーカー出しを通電確認してそのまま送ります。 ※VTXは内蔵ではありません。 ※※BetaFPVより現在はファームウェアのUPしないようにの通達が来ています。 betaflight_4.2.11_BETAFPVF411RX for SPI Frsky RX version より上のファームアップしたときはRXROSSの可能性が高い不具合が出ますので 今のところファームアップは行わないで下さい。 ここから Betaflight Firmware and CLI F4 1S 5A AIO Brushless Flight Controller comes with the default firmware betaflight_4.3.1_BETAFPVF411 (ELRS) or betaflight_4.2.11_BETAFPVF411RX (Frsky). The default firmware for Serial ExpressLRS 2.4G RX version supports ELRS V2.4 RX. Pay attention, For the Serial ExpressLRS 2.4G version, ONLY the Betaflight firmware 4.3.0 and up start to support this BMI270 gyro. For the SPI Frsky version, DO NOT flash the other firmware, otherwise, the RX will be lost in control at a very close range. We have already built our own firmware betaflight_4.2.11_BETAFPVF411RX for SPI Frsky RX version to support BMI270 gyro. Please check the below link to download the firmware. ここまで ※この製品は日本語マニュアルもなくかなり設定が難しいので【玄人向け】とさせていただきます。BetaFPVサイトで理解できる方のみご購入下さい。 【玄人向け】マニュアルはありませんので下記URLをご参照に設定してください。 https://betafpv.com/collections/components/products/f4-1s-5a-aio-brushless-flight-controller-elrs-2-4g?variant=39968364789894 BIND 裏面最上部にBINDボタンがあります。 デフォルトはFrsky_Xです。FutabaなどはBetaflightでお客様のほうで変更してください。 Specification of FC CPU: STM32F411CEU6 (100MHZ) Six-Axis: BMI270 Built-in Receiver: Serial ExpressLRS 2.4G/SPI CC2500 (Frsky) Receiver antenna: Line antenna FC Size: 30*30mm Mounting Hole Size: 26*26mm Firmware version: betaflight_4.3.1_BETAFPVF411 (ELRS)/betaflight_4.2.11_BETAFPVF411RX (Frsky) OSD: Built-in BetaFlight OSD Blackbox: 8MB Recommend VTX: >=200mW, like BETAFPV M03 350mW VTX or TBS Unify VTX Power Cable: 55mm, with BT2.0 connector Weight: 3.6g(ELRS)/3.7g(Frsky), without power cable and BT2.0 connector Specification of ESC Power supply: 1S Current: 5A continuous and peak 6A (3 seconds) ESC firmware: A_X_5_.HEX for BB51 BLHeli_S hardware Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM SPI Frsky RX Come with the built-in SPI Frsky Receiver (CC2500 chip), F4 1S 5A AIO FC can be compatible with Futaba S-FHSS, Frsky D8, and D16 protocol. The default protocol is configured to Frsky D16 FCC out of the factory. Pilots could set up the protocol according to your own need in Betaflight Configurator. Configuration Protocol FRSKY_D Frsky D8 FRSKY_X Frsky D16 FCC (ACCST 1.X version) FRSKY_X_LBT Frsky D16 LBT (ACCST 1.X version) SFHSS Futaba S-FHSS Recommend Parts Battery: BT2.0 300mAh 1S Battery Frame: Meteor65 frame / Meteor75 frame Props: 31mm 4-Blades props (for 65mm frame) / 40mm 4-blades props (for 75mm frame) Motors: 0603 motors / 0703 motors / 0802 motors VTX: M03 25-350mW VTX Package 1 * F4 1S 5A AIO Brushless Flight Controller (ELRS or Frsky) 4 * M1.2x4mm Screws 4 * M1.4x5mm Screws 4 * Anti-vibration Rubber Dampers ※半田付けしたものやファームアップしたものは返品できませんのでご注意願います。
¥5,900
【玄人向け】【ELRSV3】BetaFPV F4 1S 5A AIO Brushless Flight Controller (ELRSV3 2.4G) 2022
【玄人向け】【ELRSV3】BetaFPV F4 1S 5A AIO Brushless Flight Controller (ELRSV3 2.4G) 2022
ELRSV3 2.4G用ロングレンジモジュール 【ELRSV3】BetaFPV F4 1S 5A AIO Brushless Flight Controller (ELRS 2.4G) Meteor2022モデル (meteor65 / 65pro / 75 / メーカ出荷) のまま からお選び下さい。 ※ELRSV3になりますのでご注意ください。 ※メーカー出しを通電確認してそのまま送ります。 ※VTXは内蔵ではありません。 ※この製品は日本語マニュアルもなくかなり設定が難しいので【玄人向け】とさせていただきます。BetaFPVサイトで理解できる方のみご購入下さい。 【玄人向け】マニュアルはありませんので下記URLをご参照に設定してください。 https://betafpv.com/collections/brushless-flight-controller/products/f4-1s-5a-aio-brushless-flight-controller-elrs-2-4g?variant=39968364757126 【ExpresLRS Radio Link】 https://support.betafpv.com/hc/en-us/sections/4402604654873-ExpresLRS-Radio-Link ロングレンジELRS受信機内蔵のAIOフライトコントローラー Specification of FC CPU: STM32F411CEU6 (100MHZ) Six-Axis: BMI270 Built-in Receiver: Serial ExpressLRS 2.4G/SPI CC2500 (Frsky) Receiver antenna: Line antenna FC Size: 30*30mm Mounting Hole Size: 26*26mm Firmware version: betaflight_4.3.1_BETAFPVF411 (ELRS)/betaflight_4.2.11_BETAFPVF411RX (Frsky) OSD: Built-in BetaFlight OSD Blackbox: 8MB Recommend VTX: >=200mW, like BETAFPV M03 350mW VTX or TBS Unify VTX Power Cable: 55mm, with BT2.0 connector Weight: 3.6g(ELRS)/3.7g(Frsky), without power cable and BT2.0 connector Specification of ESC Power supply: 1S Current: 5A continuous and peak 6A (3 seconds) ESC firmware: A_X_5_.HEX for BB51 BLHeli_S hardware Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM Recommend Parts Battery: BT2.0 300mAh 1S Battery Frame: Meteor65 frame / Meteor75 frame Props: 31mm 4-Blades props (for 65mm frame) / 40mm 4-blades props (for 75mm frame) Motors: 0603 motors / 0703 motors / 0802 motors VTX: M03 25-350mW VTX Package 1 * F4 1S 5A AIO Brushless Flight Controller (ELRS or Frsky) 4 * M1.2x4mm Screws 4 * M1.4x5mm Screws 4 * Anti-vibration Rubber Dampers
¥6,000 SOLD OUT
【Beta65SV2純正ブラシFC】 BetaFPV F4 Brushed Flight Controller V2 BT2.0 内蔵レシーバーRX Frsky / SFHSS
【Beta65SV2純正ブラシFC】 BetaFPV F4 Brushed Flight Controller V2 BT2.0 内蔵レシーバーRX Frsky / SFHSS
BetaFPV F4 Brushed Flight Controller V2 BT2.0 内蔵レシーバーRX Frsky / SFHSS Beta65SV2純正ブラシFC ※BT2.0コネクターです。 内蔵レシーバーRX Frsky / SFHSS ※Beta65S 純正FCですESC/レシーバー内蔵の超軽量FCです。 ※マニュアルはありません。メーカーのHPをご参照下さい。 https://betafpv.com/collections/brushed-flight-controller/products/f4-brushed-flight-controller ※3種類から選択してください。(販売のBeta65S機体のdumpを入れます。) Frsky(Beta65SV2) S-FHSS(Beta65SV2) メーカー出荷のまま(Futaba) を選択してください。 Specification CPU: STM32F411CEU6 Six-Axis: MPU6500 ESC: All FETs are rated at 30A maximum Motor: Support 6x15mm/7x16mm/8x20mm/8.5x20mm etc motors. Recommend BETAFPV 7x16mm Brushed Motors (2CW+2CCW) Size: 26mm x 26mm, fully compatible with the Inductrix quad frame and mounting pattern Firmware version: Betaflight BETAFPVF411RX 4.2.11 OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode) Receiver: SPI Frsky D8 (CC2500 chip, adjustable) Power Cable: 55mm, with BT2.0 Connector Weight: 3.68g (with Power Cable) RECOMMENDED PARTS LIST Battery: BT2.0 300mAh 1S Battery Frame: 65mm Micro Whoop Frame Props: 31mm 3-Blade Motors: BETAFPV 7x16mm Brushed Motors (2CW+2CCW) VTX: M03 25-350mW VTX Recommend drones: Beta65S BNF Micro Whoop Quadcopter Package 1 * F4 Brushed Flight Controller (BT2.0 Connector) 4 * M1.2x4mm screws 4 * M1.4x5mm screws 4 * Anti-vibration rubber dampers
¥4,800
【NBD NEWモデル】【玄人向けELRSV2】HummingBird F4 V2 Flight Controller ELRSV2
【NBD NEWモデル】【玄人向けELRSV2】HummingBird F4 V2 Flight Controller ELRSV2
【玄人向けELRSV2】HummingBird F4 V2 Flight Controller ELRSV2 ※ELRSV2になりますのでご注意ください。 ※この製品は日本語マニュアルもなくかなり設定が難しいので【玄人向け】とさせていただきます。NBDサイトで理解できる方のみご購入下さい。 【玄人向け】マニュアルはありませんので下記URLをご参照に設定してください。 https://newbeedrone.com/products/hummingbird-f4-v2-flight-controller バインド方法(ELRSV2) ELRSV1では接続できませんのでご注意願います。ELRSのバインド方法は色々ございますのでサポート外とさせていただきます。バインディングフレーズ設定の際はお客様で設定をお願いします。 ELRSV2のプロポをバインド待ちにして、BetaFlight 以上で受信機タブのバインドボタンを押す。(機体裏のバインドボタンを押す) Specification: STM-F411 MCU for the main controller (Preloaded with Betaflight) Support 1S battery ONLY Current sensor onboard ESC-12A Per Motor Channel BB21 MCU BlHeliS Support DShot(150 300 600) Multishot Gyro- BMI270 Onboard Sideway RGB LED controlled by Betaflight Support BeeSign signal compatible with NBD VTX-Camera System Onboard Diversity SPI SX1280 Receiver(EXPRESSLRS ) MotorPlug JST1.0 NBD OSD(Betaflight OSD Compatible) 5V 2A Power support for external VTX Camera Or Receiver. Weight: 4.27g include power cable and PH2.0 Plug, 3.45g without motor plugs/pigtails BeeSign: BeeSign is a protocol created by the NewBeeDrone engineering team. It is used to communicate between the flight controller and the onboard VTX OSD (NewBeeDrone Mark1,2,3 Series Video Transmitter) ※系統図は現在付きません。 ※日本語マニュアルは現在付きません。
¥8,400
【玄人向け】BetaFPV 1-2S 12A AIO Brushless Flight Controller 2022 SPI (Frsky / S-FHSS)
【玄人向け】BetaFPV 1-2S 12A AIO Brushless Flight Controller 2022 SPI (Frsky / S-FHSS)
※Meteor85モデル (メーカ出荷)  (Futaba F-SHSS / FrskyX) からお選び下さい。  ※BINDは表面のRXボタンを押すことでBIND待ちとなります。 ※メーカー出しを通電確認してそのまま送ります。 ※VTXは内蔵ではありません。 ※この製品は日本語マニュアルもなくかなり設定が難しいので【玄人向け】とさせていただきます。BetaFPVサイトで理解できる方のみご購入下さい。 【玄人向け】マニュアルはありませんので下記URLをご参照に設定してください。 https://betafpv.com/collections/brushless-flight-controller/products/f4-1s-12a-flight-controller?variant=39921521524870 Specification of FC Item: F4 1S 12A AIO FC Weight: 4.74 g (without power cable and BT2.0 connector) CPU: STM32F411CEU6 (100MHZ ) Six-Axis: BMI270 (SPI connection) Firmware version: betaflight_4.3.1_BETAFPVF4SX1280 OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode) Receiver: SPI ELRS 2.4G Receiver Motor Pin Connector: 1.25mm Header Pins Mounting Hole Size: 26mm x 26mm (suitable for whoop pattern mounting hole) USB Port: SH1.0 4-Pin Specification of 1S 12A ESC Built-in ESC with 12A continuous and peak 25A current Input voltage: 1S-2S ESC firmware: C_X_30_REV16_7.hex for BB51 BLHeli_S hardware Signal support: D-shot150, D- shot300, D-shot600, Oneshot125, Multishot, PWM Recommend Parts If you want to try the popular ExpressLRS receiver version for long-range performance, highly recommend you check the items for the ExpressLRS series. Drones: Cetus X, 85mm whoop frame like Meteor85, 3" toothpick drones Battery: BT2.0 450mAh 1S 30C Battery Motor: 1102 18000KV motor, 1103 11000KV motor Propeller: HQ3020 2-blade Props, 2020 4-blade Props Package 1 * F4 1S 12A AIO FC 4 * Anti-vibration Rubber Dampers 4 * M2 x 10mm Screws 4 * M2 x 10mm Screws 4 * M2 Screw Nut 8 * PH-1.25 Connectors for Motor 1 * SH1.0 4-Pin Cable 1 * SH1.0 4-Pin to USB Type-C Adapter
¥6,500
【玄人向け】【ELRSV2】F4 1-2S 12A AIO Brushless Flight Controller 2022
【玄人向け】【ELRSV2】F4 1-2S 12A AIO Brushless Flight Controller 2022
ELRSV2 2.4G用ロングレンジモジュール 【ELRSV2】F4 1-2S 12A AIO Brushless Flight Controller 2022  ※ELRSV2になりますのでご注意ください。 ※BINDは表面のRXボタンを押すことでBIND待ちとなります。 ※メーカー出しを通電確認してそのまま送ります。 ※VTXは内蔵ではありません。 ※この製品は日本語マニュアルもなくかなり設定が難しいので【玄人向け】とさせていただきます。BetaFPVサイトで理解できる方のみご購入下さい。 【玄人向け】マニュアルはありませんので下記URLをご参照に設定してください。 https://betafpv.com/collections/brushless-flight-controller/products/f4-1s-12a-flight-controller 【ExpresLRS Radio Link】 https://support.betafpv.com/hc/en-us/sections/4402604654873-ExpresLRS-Radio-Link ロングレンジELRS受信機内蔵のAIOフライトコントローラー Specification of FC Item: F4 1S 12A AIO FC Weight: 4.74 g (without power cable and BT2.0 connector) CPU: STM32F411CEU6 (100MHZ ) Six-Axis: BMI270 (SPI connection) Firmware version: betaflight_4.3.1_BETAFPVF4SX1280 OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode) Receiver: SPI ELRS 2.4G Receiver Motor Pin Connector: 1.25mm Header Pins Mounting Hole Size: 26mm x 26mm (suitable for whoop pattern mounting hole) USB Port: SH1.0 4-Pin Specification of 1S 12A ESC Built-in ESC with 12A continuous and peak 25A current Input voltage: 1S-2S ESC firmware: C_X_30_REV16_7.hex for BB51 BLHeli_S hardware Signal support: D-shot150, D- shot300, D-shot600, Oneshot125, Multishot, PWM Recommend Parts If you want to try the popular ExpressLRS receiver version for long-range performance, highly recommend you check the items for the ExpressLRS series. Drones: Cetus X, 85mm whoop frame like Meteor85, 3" toothpick drones Battery: BT2.0 450mAh 1S 30C Battery Motor: 1102 18000KV motor, 1103 11000KV motor Propeller: HQ3020 2-blade Props, 2020 4-blade Props Package 1 * F4 1S 12A AIO FC 4 * Anti-vibration Rubber Dampers 4 * M2 x 10mm Screws 4 * M2 x 10mm Screws 4 * M2 Screw Nut 8 * PH-1.25 Connectors for Motor 1 * SH1.0 4-Pin Cable 1 * SH1.0 4-Pin to USB Type-C Adapter
¥6,500
【Mobula7純正FC】 Crazybee X12 AIO 400mW 5in1 Flight controller SPI Frsky/SFHSS ESC12A/VTX/レシーバー内蔵フライトコントローラー
【Mobula7純正FC】 Crazybee X12 AIO 400mW 5in1 Flight controller SPI Frsky/SFHSS ESC12A/VTX/レシーバー内蔵フライトコントローラー
【Mobula7純正FC】 Crazybee X12 AIO 400mW 5in1 Flight controller built-in SPI Frsky/SFHSS ESC/VTX/レシーバー内蔵フライトコントローラー(ファームBF 4.3.0) 内蔵レシーバーRX Frsky / SFHSS 1-2S対応 ESC:12A レシーバ付き・VTXも400mWのハイパワーが付属したF4オールインワンFC+ESC+VTX メーカー出荷のまま(FrskyD)で発送します。 ※Mobula7 純正FCですESC/VTX/レシーバー内蔵の超軽量FCです。 ※系統図は付けますがマニュアルは付いていません。 Specifications: Brand Name: Happymodel Item Name: X12 AIO 5-IN-1 Flight controller built-in 12A ESC and OPENVTX Betaflight firmware target: FRSKY Version:CRAZYBEEF4FR VTX antenna: U.FL Weight: 5.1g Support 1-2S Lipo/LIHV battery Size: 30mm*30mm*8mm Flight controller MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU6000 or ICM20689 or BMI270(SPI connection) Mount hole size: 25.5mm*25.5mm Power supply: 1-2S battery input (DC 2.9V-8.7V) Built-in 12A(each) Blheli_S 4in1 ESC Built-in Betaflight OSD(SPI Control) Built-in 5.8G OpenVTX 0mw~400mw Built-in ExpressLRS 2.4G,Frsky D8/D16 Built-in voltage meter sensor , voltage meter scale 110Built-in current meter sensor , current meter scale 470 Onboard SPI 2.4GHz Receiver SPI BUS receiver CC2500 RF Compatible Non EU transmitter D8 model Channels: 8ch No ground interference ( Transmitter and receiver 1 m from the ground): 200meterFailsafe support Support Frsky D8/ D16 , Redpine , SFHSS Onboard 5.8g Openvtx Output power: 0mw~400mw switchable Frequency: 40CH Input voltage: 3.3V 5.5V Current consumption: 300mA(type) Frequency: 5.8GHz 5bands 40 channels(include Race band)Smartaudio ready
¥11,800
【PAVO30純正FC】 Toothpick F722 2-6S AIO Brushless Flight Controller 35A(BLHeli_S)
【PAVO30純正FC】 Toothpick F722 2-6S AIO Brushless Flight Controller 35A(BLHeli_S)
【PAVO30純正FC】 Toothpick F722 2-6S AIO Brushless Flight Controller 35A(BLHeli_S) ※XT60コネクター付属です。 ※レシーバーは付いていません。 ※マニュアルは付いていませんのでメーカーのHPをご参照下さい。 https://betafpv.com/collections/brushless-flight-controller/products/toothpick-f722-2-6s-aio-brushless-flight-controller-35ablheli_s Specification of FC Item: F722 35A AIO FC(BLHeli_S) Weight: 7.06g CPU: STM32F722RET6 Six-Axis: MPU6000 (SPI connection) Mounting hole size: 26mm * 26mm Firmware version: betaflight_4.2.x_BETAFPVF722 OSD: Built-in BetaFlight OSD (OSD chip: AT7456E) Support programmable LED like WS2812 etc Built-in current sensor Specification of ESC Signal support: PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600 Receiver: Support Frsky XM/XM+ Receiver/ Futaba Receiver/Flysky Receiver/DSMX Receiver/TBS Crossfire Receiver (requires external connection) Input voltage: 2S-6S Lipo Continuous current: 35A Peak current: 40A ESC firmware: BLHeli_S Indicators: 2 indicators: receiver indicator (green)/Flight control power indicator (red) Capacitance: CS|5*10*13mm|470μF|35V Connecter: 80mm 14AWG silicone cable with XT60 Recommended motors: 14XX series, 15XX series, 16XX series, 18XX series, 20XX series 仕様: ブランド名:BetaFPV F4 2-4S AIO Brushless Flight Controller 12A V3 モデル:Beta75X/85X Package 1 * Toothpick F722 35A AIO 2-6S brushless flight controller 1 * Cable Pigtail (XT60U) 1 * Capacitance 1 * 6-Pin Connector for DJI Digital VTX 4 * M2x10mm Screws 8 * M2 Nuts
¥11,200 SOLD OUT
【玄人向】RadioMaster R81 2.4GHz 8CH Over 1KM SBUS Nano Receiver レシーバー(FrskyD8)
【玄人向】RadioMaster R81 2.4GHz 8CH Over 1KM SBUS Nano Receiver レシーバー(FrskyD8)
RadioMaster R81 2.4GHz 8CH Over 1KM SBUS Nano Receiver レシーバー(FrskyD8) 説明書はありません。 SBUS接続でFrskyD8プロトコルです。 Description: Brand Name: RadioMaster Item Name: R81 Nano Receiver Model: R81 Weight: 2g Size: 17*11 mm Channels: 8CH Frequency range: 2400-2483.5Mhz Power input range: 4.5-6V Signal format: Frsky D8 Compatible Output format: SBUS Support return: support return RSSI Control distance: more than 1km Antenna length: Approximaltly 6cm Bind method: 1. Press and hold the BIND button on the receiver then connect power. After approximately 3 seconds, the receiver LED will be RED, the receiver is now in bind mode 2. Select the D8 protocol for the multi-protocol menu of your remote control, and press the [BIND] option, the red light of the receiver will flash indicating successful bind 3. Exit bind mode on your remote control and disconnect power to the receiver then power the receiver once more. The LED will now be solid RED indicated the bind is now done. If not please repeat step 1 and 2 Fail-safe Protection: 1. Press the BIND button once within 10 seconds of th eceiver being powered on, and the receiver will save all the current channel values of the remote control as the fail-safe value 2. 10 seconds after the receiver is powered on, the BIND button function will be disabled to prevent accidental changes to to the fail-safe settings while preparing the model for flight RSSI output: This receiver has a total of 9 channels. 8 channels + an RSSI output channel. Channels 1-8 are controlled by the remote controller, the 9th channel is the signal strength RSSI value output by the receiver itself, which can be read by the flight controller and sent to the OSD device Show signal strength. Package Included: 1 x R81 Nano Receiver
¥3,000
【リモートID】 リモートID 小型無人航空機用 BVRPA(20mmx20mm)Braveridge社
【リモートID】 リモートID 小型無人航空機用 BVRPA(20mmx20mm)Braveridge社
リモートID 小型無人航空機用 BVRPA(20mmx20mm) 小型のドローンにも対応する軽量なリモートID バッテリーレスで電源を取るだけでOK 1SHV/Lipo バッテリーも利用可 FCサイズなのでレーシングドローンなどにも容易に搭載できます 内蔵式アンテナ 軽量8.5gで100gを超えるマイクロドローンにも対応します! 電源供給用のコネクターには、GHコネクタ2極(JST)を採用 また、2系統の端子を装備し幅広い電圧入力にも対応 供給電圧 ・5ー55V ・3.6ー9V 2灯のフルカラーLEDを装備しており、電源のON/OFF状態や、configモード、発信、GNSS取得中などの状況が確認可能 メーカーリモートIDポータルサイト: https://www.braveridge.com/product_support/remoteid/ 取扱い説明書: https://drive.google.com/file/d/1RLl0hqMr3qoJ1YZYc0phDOxAaT7yrTwg/view リモートID書き込み方法: https://drive.google.com/file/d/1RM3TcHLVA8uRfO1_oJP7o2I9tM2xi5AQ/view リモートID FAQ : https://www.braveridge.com/product_support/remoteid/faq/archives/category/remoteid/remoteid_product ※機体への装着や別電源にて外付けなど別料金にて対応いたします 国土交通省仕様準拠 外形寸法 40 x 40 mm(ネジ止め寸法:20 x 20 mm) 本体重量 8.5 g 表示 フルカラーLED×2 スイッチ 1個 電源コネクタ GHコネクタ2極(JST) 電源 ドローン本体より供給(3.6~9V、5~55Vの2系統) 無線 Bluetooth® 5.0 LongRange(BVMCN52840CFSLR) センサー GNSS(BVMGPS5605S) 認証 日本電波法、Bluetooth® SIG認証 リモートID機器の搭載義務化について ドローンなどの無人航空機の利用が急速に拡大するなか、航空法改正により、2022年6月20日から100g以上の無人航空機(ドローン、ラジコン機など)にはリモートID機器の搭載が義務化されます リモートIDは自動車のナンバープレートのようなもので、リモートID機器から電波で機体の識別信号を発信することによって飛行中の機体の登録を判別可能にします パッケージ: BVRPA 1枚 日本語説明書 パッケージにメーカー保証書が付いています。
¥15,900
【玄人向け】Happymodel CrazyF411 AIO F4 Flight Controller Built-in 20A ESC/OSD/Frsky Receiver ESC/レシーバー内蔵フライトコントローラー
【玄人向け】Happymodel CrazyF411 AIO F4 Flight Controller Built-in 20A ESC/OSD/Frsky Receiver ESC/レシーバー内蔵フライトコントローラー
Happymodel CrazyF411 AIO F4 Flight Controller Built-in 20A ESC/OSD/Frsky Receiver ESC/レシーバー内蔵フライトコントローラー 内蔵レシーバーRX Frsky / SFHSS ※【玄人向け】モーターも半田付け使用です。(モーターコネクターパーツ付属) ※【玄人向け】ファームアップなどすれば確実に飛ばなくなりますのでご注意願います。 ※【玄人向け】メーカー出荷のまま はかなりのスキルが無ければ飛行できません。 CrazyF411 pro is a highly packed 6.3g 2-4S AIO F4 flight controller with built in 20/25A per channel ESC and diversity receiver. Low latency D8/D16 Futaba S-FHSS Redpine protocol with dual IPEX UFL Antenna (with Power amplifier) Large soldering pads with 4 angled motor connector (not soldered) 2 complete UART (UART 1 with inverted PX pad) Compatible with 110x/120X/130X/140X motors Integrated with F411 processor, Betaflight OSD, 5V 1.5A BEC Flight controller MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 2-4S battery input (DC 8V-17V) Built-in 20A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Frsky D8/D16 SPI receiverBuilt-in 2.4G Power Amplification Built-in Betaflight OSD(SPI Control) Built-in Current meter Built-in 5V 1.5A BEC Built-in voltage detection Firmware target: MATEKF411RX Yaw Degrees should set to “-90 degree” to match the flight direction Onboard 4in1 ESC MCU upgraded to EFM8BB21 Power supply: 2-4S LiPo/LiPo HV (7v/17v) Current: 20A continuous peak 25A (5 seconds) Support BLHeliSuite programmable Factory firmware: F_H_40_REV16_7.HEX Default protocol: DSHOT600 Internal Frsky NON-EU receiver Version SPI BUS receiver Frsky D8/D16 compatibleCompatible Non EU transmitter both D8 mode and D16 mode Channels: 8ch/16chDual antenna Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 400m Bind procedure: Make the on board receiver get into bind mode: For 4.0.x version firmware Plug USB and then connect betaflight configurator and then move to CLI tab , type “bind_rx_spi” ,the Red LED on the top of the flight controller will getting to be solid , the onboard receiver is in bind mode; For 4.1.x or 4.2.x the bind code is “bind_rx” Make your transmitter get into bind mode . If bind is successful the red led will starting to blink. The red LED wouldn’t blinking when binding with some new ACCESS firmware frsky radio , but the bind is actual successful , need to go to CLI command and type “save” to finish the binding . SPI Receiver option – all selectable in Betaflight Frsky_D compatible with Frsky D8 protocol Frsky_X compatible with Frsky non-eu D16 protocol Frsky_X_LBT compatible with Frsky EU-LBT D16 protocol (4.0.X or latest betaflight firmware support) SFHSS compatible with Futaba S-FHSS protocol パッケージ: F411FC 1枚 RXアンテナ 2本 XT30コネクターケーブル モーター用コネクター ネジセット
¥10,500
【Beta65S純正ブラシFC】 BetaFPV F4 1S Brushed Flight Controller 内蔵レシーバーRX Frsky / SFHSS
【Beta65S純正ブラシFC】 BetaFPV F4 1S Brushed Flight Controller 内蔵レシーバーRX Frsky / SFHSS
Beta65S純正ブラシFC ※PH2.0コネクターです。 内蔵レシーバーRX Frsky / SFHSS ※Beta65S 純正FCですESC/レシーバー内蔵の超軽量FCです。 ※マニュアルはありません。メーカーのHPをご参照下さい。 https://betafpv.com/collections/brushed-flight-controller/products/f4-brushed-flight-controller-frsky-rx-osd ※3種類から選択してください。(販売のBeta65S機体のdumpを入れます。) Frsky(Beta65S) S-FHSS(Beta65S) メーカー出荷のまま(Futaba) を選択してください。 SPECIFICATIONS OF FC CPU: STM32F411CEU6 (100MHZ ) Six-Axis: MPU-6000 triaxial accelerometer / triaxial gyroscope (SPI connection) Size: 26mm x 26mm, fully compatible with the all whoop drone mounting pattern, recommend the Beta65X frame and Beta75 Pro frame. Firmware version: betaflight_matekf411rx_4.0.0 (Development Version) OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode) Built-in SPI Frsky D16 protocol native receiver, compatible with almost ALL Frsky FCC radios(e.g. Taranis X9D/X9D Plus/X7) or Frsky compatible transmitter module. Not compatible with Frsky LBT protocol. Power Cable: 55mm, with 2pcs JST-PH 2.0 connector, AKA PowerWhoop connector Weight: 4.5g Specifications CPU: STM32F411CEU6 Six-Axis: MPU6000 ESC: All FETs are rated at 30A maximum. Support 6x15mm/7x20mm/8x20mm/8.5x20mm etc motors. Size: 26mm x 26mm,fully compatible with the Inductrix quad frame and mounting pattern Firmware version: Betaflight MATEKF411RX 3.4.0 for F4 Brushed FC (SPI Frsky RX) Firmware version: Betaflight MATEKF411 for F4 Brushed FC (No RX) OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode) Receiver: SPI Frsky D16 protocol (AKA FRSKY_X on Betaflight Configuration) Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector Weight: 3.7g 仕様: ブランド名:BetaFPV F4 1S Brushed Flight Controller モデル:Beta65S パッケージ: F4FC 1枚 ネジセット
¥4,000 SOLD OUT
【玄人向け】【ELRSV2】BetaFPV F4 1S 5A AIO Brushless Flight Controller (ELRSV2 2.4G)
【玄人向け】【ELRSV2】BetaFPV F4 1S 5A AIO Brushless Flight Controller (ELRSV2 2.4G)
ELRSV2 2.4G用ロングレンジモジュール 【ELRSV2】BetaFPV F4 1S 5A AIO Brushless Flight Controller (ELRS 2.4G) ※ELRSV2になりますのでご注意ください。 ※メーカー出しを通電確認してそのまま送ります。 ※VTXは内蔵ではありません。 ※この製品は日本語マニュアルもなくかなり設定が難しいので【玄人向け】とさせていただきます。BetaFPVサイトで理解できる方のみご購入下さい。 【玄人向け】マニュアルはありませんので下記URLをご参照に設定してください。 https://betafpv.com/collections/expresslrs-series/products/f4-1s-5a-aio-brushless-flight-controller-elrs-2-4g 【ExpresLRS Radio Link】 https://support.betafpv.com/hc/en-us/sections/4402604654873-ExpresLRS-Radio-Link ロングレンジELRS受信機内蔵のAIOフライトコントローラー SPECIFICATIONS OF FC CPU: STM32F411CEU6 ( 100MHZ ) Six-Axis: ICM-20689/MPU-6000 Built-in Receiver: SPI ExpressLRS 2.4G Receiver antenna: 2.4GHz SMD ceramic antenna Size: 29mm x 29mm, fully mounting pattern compatible with the whoop frame in the current market Firmware version: betaflight_4.3.0_STM32F411_norevision OSD: Built-in BetaFlight OSD Recommend VTX: >=200mW, like BETAFPV M03 350mW VTX or TBS Unify VTX Power Cable: 55mm, with BT2.0 connector Weight: 3.13g (no power cable included) SPECIFICATIONS OF ESC Power supply: 1S Current: 5A continuous and peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: O_H_5_48_REV16_8.HEX Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM Betaflight Firmware and CLI Since Betaflight has not yet released the official firmware that could supports the SPI ExpressLRS protocol, the current version is the Beta version. Please use the firmware and the CLI dump file below to recovery the FC board if needed. Betaflight will update to their official target soon. Please feel free to contact with us if you have any issues with this Beta version Firmware. It is normal that there is no any option on Betaflight Configurator Receiver. As show below, the checkbox is blank. PACKAGE 1 * F4 1S brushless flight controller (BT2.0 Connector) 4 * M1.2x4mm screws 4 * M1.4x5mm screws 4 * Anti-vibration rubber dampers
¥5,800 SOLD OUT
【玄人向け】Happymodel Happymodel ELRS X2 AIO 2-4S Flight Controller Built-in SPI 2.4G ELRS and 12A ELRSレシーバー内蔵フライトコントローラー
【玄人向け】Happymodel Happymodel ELRS X2 AIO 2-4S Flight Controller Built-in SPI 2.4G ELRS and 12A ELRSレシーバー内蔵フライトコントローラー
Happymodel Happymodel ELRS X2 AIO 2-4S Flight Controller Built-in SPI 2.4G ELRS and 12A ELRSレシーバー内蔵フライトコントローラー ※【玄人向け】ELRS V2対応 ※【玄人向け】メーカー出荷のまま はかなりのスキルが無ければ飛行できません。 Specifications: Flight controller MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Mount pattern: 25.5×25.5 M2 Power supply: 2-4S Lipo battery Built-in 12A Blheli_s ESC each Built-in Betaflight OSD(SPI Control) Built-in SPI ExpressLRS 2.4GHz receiver Built-in 5V 1A BEC Flight controller firmware target: CRAZYBEEF4SX1280 Onboard 4in1 ESC MCU upgraded to EFM8BB21 Power supply: 2-4S LiPo/LiPo HV (7v/17v) Currents: 12A continuous peak 15A (5 seconds) Support BLHeliSuite programmable Factory firmware: F_H_40_REV16_8.HEX Default protocol: DSHOT150/DSHOT300/DSHOT600 Onboard SPI ExpressLRS 2.4GHz Receiver Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz RF Frequency: 2.4GHz Antenna: On board SMD ceramic antenna Telemetry output Power: <12dBm Receiver protocol: SPI ExpressLRS Could bind with ELRS 2.4Ghz TX module(Recommend TX module with latest elrs firmware) Onboard voltage and Amperage meters settings Voltage meter scale setting 110 Amperage meter scale setting 470 Package Included: 1*Happymodel ELRS X2 AIO 2-4S Flight controller
¥10,300 SOLD OUT
KigaruDrone

メールマガジンを受け取る