• shopping cart
※土曜・日曜・祝日の発送はありません。※10月1日より日本郵便値上げの為、送料の変更を行いました。

TUNERC

Poly F405 2S-4S 20A AIO V1.2 Flight Controller
Poly F405 2S-4S 20A AIO V1.2 Flight Controller
75-95サイズCineWhoopや3インチ、U99Thoothpick機に最適 安定のF405 V1.2になりました。 Poly F405 2S-4S 20A AIO V1.2 Flight Controller  ※XT30コネクターです。 ※レシーバー/VTX/モーターコネクターは付いていません。 ※マニュアルは付いていませんのでメーカーのHPをご参照下さい。 https://www.tunerc.com/product/poly-f405-2s-4s-20a-aio-v1-2/ マニュアルPDFダウンロード https://www.tunerc.com/wp-content/uploads/2024/09/poly-f405-v1.2-wiring-diagram-2024-9-11.pdf ※※Poly F405 V1.2 にプリフラッシュされた ESC ファームウェアに関する注意事項 Poly F405 V1.2 のデフォルトの Bluejay ファームウェアは 0.21 です。前バージョン V0.16 よりも起動電力が低くなりました。モーターが回転しない場合は、起動電力を上げてみてください。 起動電力とモーターアイドルの設定方法については、以下の記事を参照してください。 https://github.com/bird-sanctuary/bluejay/wiki/Setup ——2024/8/27更新 Hardware Specs FC MCU: STM32F405RGT6( Cortex®-M4 168Mhz ) Built-in OSD: AT7456E Built-in IMU: BMI270 Built-in 8M Flash Blackbox Built-in Current Meter ESC MCU: EFM8BB21 ( 8bit 50MHz ) UART: UART1 ( for VTX by default ), UART2, UART3, UART4 ( supports SBUS ), UART5 Other interfaces: IIC ( IIC2 ) , LED_Strip, Buzzer The through holes for power lead: big enough to fit 16AWG wire 8 Motor Outputs ( The onboard esc have been used for 4 motor outputs. You can add 4 external esc if you want to use the other 4 motor outputs ) Electronics Specs Input Voltage: 6.50-20.0V( 2S-4S LIPO/LIHV ) Power Output: 5V 2A Continuous Current: 20A Firmware FC Betaflight Target: TUNERCF405 ESC Firmware: Bluejay P-H-25 Motor Size Supported 1102~1104, 1202~1204, 1303, 1404 Recommended Capacitor A 35V 220uf capacitor is included. A 35v 220-470 uf capacitor with low ESR is recommended if you want to swap the default one. Dimensions Size: 33mm x 33mm Mounting Holes Pattern: 25.5 x 25.5mm Room for M3.5 grommets to make M2 mount Weight: 6.1g In the box 1 * Poly F405 2S-4S 20A AIO V1.2 1 * XT30 pigtail with 18awg wire 1 * 35V 220uf capacitor 6 * grommets
¥10,000
【玄人向け】TUNERC Buzzer with Built-in Driver Circuit V2 plug Version
【玄人向け】TUNERC Buzzer with Built-in Driver Circuit V2 plug Version
75-95サイズCineWhoopや3インチ、U99Thoothpick機に最適 TUNERC Buzzer with Built-in Driver Circuit V2 plug Version ※マニュアルは付いていませんのでメーカーのHPをご参照下さい。 https://www.tunerc.com/product/buzzer-with-built-in-driver-circuit/ Specs Working Voltage: 3-5V Sound Loudness: ≥80db@3V, ≥85db@5V Length: V2: 10.5mm Height: V2: 10.5mm Weight: V2: 2.0g ( including 0.9g 200mm length wire) Wire Length: V2: 200mm Blue wire (V1): for signal White wire (V2): for signal Red wire: for 3V-5V Black wire: for GND How to Connect the Buzzer to Poly F405 2S-4S AIO? You just need to do the wiring as the diagram below. We have already done the mapping in Betaflight so you don’t need to do that in the CLI. FC 5V — Buzzer Red Wire (3V-5V) FC GND — Buzzer Black Wire (GND) FC BZ — Buzzer Blue Wire (Signal) How to Connect the Buzzer to Flight Controllers that features “Buzzer+” “Buzzer-” Soldering Pads? You just need to wire the buzzer with the flight controller as per the instruction below. And you don’t need to do the mapping in Betaflight. FC “Buzzer+” — Buzzer Red Wire (3V-5V) FC “GND”— Buzzer Black Wire (GND) FC “Buzzer-” — Buzzer Blue Wire (Signal) How to Connect the Buzzer to EZ F411 AIO and Other Flight Controllers that don’t Feature Buzzer Pads? Step 1. Firstly, please solder the buzzer’s signal wire ( blue wire) to any available/free port on the flight controller. For example, RX1 is mostly the available port on the EZ AIO, so you can connect the FC RX1 with the Buzzer Signal Wire (Blue Wire), FC 5V–Buzzer 3V-5V (Red Wire), FC GND–Buzzer GND (Black Wire)
¥900
KigaruDrone

メールマガジンを受け取る